Whole-system duct and dryer vent check with before-and-after photos - you see exactly what came out of your vents
That "$99 whole-house special" is a bait ad - the real number appears once they are in your hallway, or the "clean" is a shop-vac at the register. We photograph the inside of your ducts before and after instead.
Before
After
Before
After
Before
AfterRotobrush HVAC Cleaning in New Braunfels: What to Know First
We provide independent Rotobrush HVAC cleaning in New Braunfels for homeowners who want the work documented, not just done. A typical evaporator coil or blower cleaning runs $280-$450 for a standard residential system, and we deliver a written price before touching a single panel. Most Rotobrush jobs we handle in the Comal County area are scheduled within three to five business days, depending on parts availability.
This page is for Rotobrush owners in New Braunfels who have noticed weak airflow, musty output, or a blower that cycles louder than it used to. If that sounds familiar, call (830) 549-6847 and we’ll schedule a no-charge inspection with photo documentation.
How Rotobrush Products Fail - and How We Fix Them
- Beast Series brush motor burnout from debris overload. The Beast line’s high-torque motor pulls hard, but when the flex shaft encounters a packed plenum or collapsed flex duct, the motor overheats rather than stalling safely. We see this in New Braunfels homes near the Gruene Historic District where 1980s flex duct has narrowed with age. Our fix: inspect the full duct run with a borescope before powering the unit, then clear the restriction with a Nikro negative-pressure pre-clean so the Beast isn’t fighting a blockage it didn’t create.
- BrushMaster Pro flex-shaft fatigue at the coupler. The Pro’s quick-connect coupler wears at the 18-month mark under regular residential use, especially when operators reverse direction frequently. The symptom is a rhythmic clicking that owners mistake for bearing noise. We stock both OEM and quality aftermarket couplers, and we’ll show you the wear pattern on the old part before quoting replacement.
- Air Duct Cleaner (ADC) line vacuum motor seal degradation. The ADC’s smaller form factor runs hot in Texas attics, and the motor housing seal hardens after two to three summers. Loss of suction follows, often misdiagnosed as a clog. We replace the seal with a high-temp silicone variant rated for Comal County’s 100°F+ attic conditions, not the standard OEM spec that was designed for cooler climates.
- Beast Lite drive belt glazing from humidity cycling. New Braunfels sits in a transition zone between Hill Country dryness and Gulf moisture, and garage-stored Beast Lite units develop belt glaze from repeated expansion and contraction. The unit runs but loses brush RPM. We keep belts in stock and check pulley alignment, since the Lite’s stamped-steel bracket can shift if the unit was transported roughly between jobs.
- Older Rotobrush 400-series HEPA filter collapse. The 400’s pleated HEPA is undersized for the airflow, and when homeowners run it with a clogged pre-filter, the pleats deform and bypass unfiltered air. We document this with a pre-photo, source the correct replacement (not the generic “fits Rotobrush” knockoff that gaps at the seal), and log the pressure drop so you know the filter is actually loading, not just aging on a calendar.
Our Rotobrush HVAC Cleaning Process
- 1
Inspection with photo record. We access the air handler, photograph the evaporator coil, blower wheel, and plenum condition, then show you before quoting. Tomas Reyes started this practice after learning the trade at BOCES Westchester, and we haven’t skipped it since.
- 2
Written scope and price. Haven Standard Clause 1: the price is written, itemized, and agreed before work begins. No exceptions.
- 3
Component-specific cleaning. We match the method to the Rotobrush model and the actual contamination. A Beast cleaning a coil caked in construction dust from a recent Canyon Lake area renovation gets different chemistry than a BrushMaster Pro handling routine residential buildup.
- 4
OEM or quality aftermarket parts decision. If a part needs replacement, we explain the warranty implications of each option. Some Rotobrush components have no functional OEM equivalent anymore; when that’s the case, we name the aftermarket source so you can verify it independently.
- 5
Post-clean testing and documentation. We run the system, measure temperature split and static pressure, then photograph the cleaned components. The photo record, written scope, and 365-Day Done Right Promise go to you as a single job file.
- 6
Cleanup and scheduling note. We leave the workspace as found, note any findings that affect future maintenance (aging flex duct, undersized returns), and log the next recommended service interval based on what we actually saw.
BeforeAfterWhat Rotobrush HVAC Cleaning Costs in New Braunfels
| Service | Typical Range | What Moves the Price |
|---|---|---|
| Evaporator coil cleaning (Rotobrush-accessible) | $280-$380 | Coil fin condition, access panel location, presence of baked-on biological growth |
| Blower wheel and housing cleaning | $220-$320 | Wheel removal required vs. in-place cleaning, bearing inspection |
| Full air handler cleaning (coil + blower + plenum) | $420-$550 | System size, plenum complexity, filter rack condition |
| Condenser coil cleaning (outdoor unit) | $180-$260 | Refrigerant line protection, fin density, surrounding debris load |
| Heat exchanger inspection and cleaning | $320-$450 | Access method, combustion zone condition, camera documentation required |
These are whole-system prices, not per-vent or teaser rates that balloon on arrival. The price we write is the price you pay. Call (830) 549-6847 for a free estimate with no obligation to schedule.
Why New Braunfels Homeowners Call CleanRun Air Duct Cleaning New Braunfels for Rotobrush Work
We’ve cleaned HVAC systems in New Braunfels since 2013, and we’ve worked on enough Rotobrush equipment to know which parts fail predictably and which symptoms send you down the wrong diagnostic path. The 365-Day Done Right Promise applies to every job, backed in writing, not as a policy subject to manager approval. Our technicians are background-checked and uniformed under Haven Standard Clause 3: Verified Crews, and they arrive with equipment from Rotobrush, Nikro, Abatement Technologies, Honeywell, Aprilaire, and Guardsman - brands you can look up before we start.
We also service Lennox, Trane, and Carrier systems, so if your Rotobrush unit revealed a problem that extends beyond the component we cleaned, we can address it without a second dispatch. The photo record from your job stays on file, and Tomas Reyes reviews every scope before it goes out.
FAQs
No. Routine cleaning and maintenance by a qualified independent technician does not void the manufacturer’s warranty, provided no unauthorized parts are installed and the work is documented. We log every step and use manufacturer-specified or equivalent components, so your warranty record stays clean. Call (830) 549-6847 if you need documentation for a warranty claim.
Replacement becomes the better option when the cost of cleaning plus needed repairs exceeds 60% of a comparable new unit, or when the flex shaft shows repeated failure at multiple points. We make this assessment with photos, not pressure, and we’ll show you the wear that drives our recommendation. For a second opinion on any written estimate, bring it to us at no charge.
Yes for most Beast and BrushMaster Pro components, though some 400-series parts are discontinued. When OEM is unavailable, we source quality aftermarket alternatives and disclose the manufacturer so you can verify specifications independently. We never install “fits Rotobrush” generics that gap at seals or underspec motor loads.
A standard evaporator coil and blower cleaning takes two to three hours on site, including inspection, documentation, and post-clean testing. Full air handler jobs run three to four hours. We schedule honestly and keep our windows real, because showing up late wastes the same trust that a bait price does.
You’ll receive before-and-after images of every cleaned component: the coil face, blower wheel blades, plenum interior, and filter rack. If we found a problem we couldn’t address in the scheduled scope, that appears too, with a written note. The photo record is included on every visit, not sold as an add-on. Call (830) 549-6847 to schedule an inspection and see what your system actually looks like inside.
Written by Tomas Reyes, Owner, CleanRun Air Duct Cleaning New Braunfels at CleanRun Air Duct Cleaning New Braunfels, serving New Braunfels and nearby areas.