Whole-system duct and dryer vent check with before-and-after photos - you see exactly what came out of your vents
That "$99 whole-house special" is a bait ad - the real number appears once they are in your hallway, or the "clean" is a shop-vac at the register. We photograph the inside of your ducts before and after instead.
Before
After
Before
After
Before
AfterHoneywell HVAC Cleaning in New Braunfels: What to Know First
We provide independent Honeywell HVAC cleaning in New Braunfels, typically completing evaporator coil, blower, and condenser work in a single scheduled visit with a written price delivered before any panel comes off. Most Honeywell systems we see in New Braunfels homes run between $340 and $620 for full HVAC cleaning, depending on whether the air handler requires blower removal and whether the evaporator coil needs chemical treatment beyond standard foaming. This page is for homeowners running Honeywell Prestige, Lyric, T6 Pro, or legacy FocusPRO equipment who want the work done without voiding their warranty or being sold parts they don’t need. Call (830) 549-6847 for a free written estimate.
How Honeywell Products Fail - and How We Fix Them
- Prestige IAQ (YTHX9321R) - Blower wheel imbalance from pet hair and fine Hill Country dust. The variable-speed ECM motor in this series is sensitive to even minor imbalance. In New Braunfels, where caliche dust infiltrates older homes near Gruene, we’ve found blower wheels caked to the point where the motor draws 15% more amperage than spec. We remove the blower assembly, clean the wheel on a bench with compressed air and soft-bristle agitation, then rebalance before reinstalling. No motor replacement needed in 90% of cases.
- Lyric T6 Pro Wi-Fi (RCHT8612WF) - Frozen coil from restricted airflow at the evaporator. The T6 Pro’s tight temperature deadband (0.5°F default) cycles the compressor aggressively. When the evaporator coil is fouled with biofilm from our high-humidity springs, the coil freezes between cycles, then defrosts into the return plenum. We pull the coil, apply foaming cleaner followed by low-pressure rinse, then set the stat to a wider 1.5°F differential to reduce short-cycling stress.
- FocusPRO 5000/6000 (TH5110D/TH6110D) - Heat exchanger sooting from delayed ignition due to dirty burners. These older non-communicating systems still populate homes built 2010-2016 in Creekside and River Chase. The crossover ports on Honeywell’s OEM burner design clog with spider webs and dust, causing rollout that soils the primary heat exchanger. We pull and sonic-clean the burners, then scope the exchanger with a borescope to document integrity before reassembly.
- Whole-home humidifier (HE360A) - Pad frame corrosion and solenoid failure from mineral scale. The HE360A’s flow-through design is standard on many Honeywell furnace installations here, but our hard Comal County water calcifies the distribution tray in 18-24 months. We descale the frame, replace the pad with an OEM Honeywell HC26A1008 (not the generic blue aftermarket that wicks unevenly), and test solenoid amp draw. If it’s above 0.3A, we quote replacement before it sticks open and floods the return.
- Zone panel (HZ432) - Damper actuator sluggishness from debris in the plenum. TrueZONE panels often get blamed for damper failure when the real issue is debris loading the damper blade. In two-story homes near Fischer Store Road, we’ve found flexible duct collapses upstream forcing the actuator to work against static pressure it wasn’t designed for. We clean the duct run, verify full damper stroke with a manometer, and only then replace the actuator if the motor ohms out of spec.
Our Honeywell HVAC Cleaning Process
- 1
Systematic inspection with photo documentation. We photograph the evaporator coil, blower wheel, condenser fins, and heat exchanger before touching anything. Tomas Reyes started this practice after his BOCES Westchester training: show the photo first, explain what you’re looking at, then talk about what happens next.
- 2
Written scope and price under Haven Standard Clause 1. You get a line-item written price before any work begins. If we find additional issues during cleaning, we stop, photograph, and write a revised scope. No surprises.
- 3
OEM-vs-aftermarket parts decision, documented. For Honeywell components, we stock OEM pads, sensors, and ignitors. When a quality aftermarket equivalent meets manufacturer spec (some solenoids, pressure switches), we note the source and warranty term in writing.
- 4
Cleaning execution with trade-specified methods. Evaporator coils get foaming cleaner with proper dwell time; blower wheels get bench cleaning, not in-place vacuuming that misses the backside; condensers get fin straightening before chemical cleaning to prevent acid etching.
- 5
Post-clean testing and photo record delivery. We measure static pressure, temperature split, and amp draw against Honeywell’s published specs. The before-and-after photo record, written scope, and 365-Day Done Right Promise document are delivered before we leave.
- 6
Cleanup and scheduling of any follow-up. We verify no residual cleaner odor, confirm drain pan flow, and note the next recommended service interval based on what we found.
BeforeAfterWhat Honeywell HVAC Cleaning Costs in New Braunfels
| Service | Typical Range | What Moves the Price |
|---|---|---|
| Evaporator coil cleaning (accessible, foaming treatment) | $340-$420 | Coil depth, fin corrosion, need for biocide treatment |
| Blower assembly removal and cleaning | $180-$260 | Motor type (PSC vs ECM), wheel condition, access panel configuration |
| Condenser coil cleaning (outdoor unit) | $160-$240 | Fence proximity, fin damage, refrigerant line insulation condition |
| Full HVAC cleaning (coil + blower + condenser) | $520-$620 | System age, prior maintenance history, duct leakage affecting load |
| Heat exchanger inspection and burner cleaning | $280-$380 | Burner count, exchanger material (tubular vs clamshell), borescope access |
Price is determined by what your system actually needs, not by a flat rate that hides shortcuts or a per-vent structure that doesn’t apply to HVAC component cleaning. Every estimate is free, written, and valid for 30 days. Call (830) 549-6847.
Why New Braunfels Homeowners Call CleanRun Air Duct Cleaning New Braunfels for Honeywell Work
We’ve cleaned Honeywell equipment in New Braunfels since 2013, including the transition years when the company shifted from the FocusPRO line to the Lyric ecosystem. That history matters when a technician needs to know whether your zone panel communicates over RedLINK or conventional 24V wiring before opening the cover.
Our 365-Day Done Right Promise is backed in writing on every job, not stated in marketing copy and forgotten. Haven Standard Clause 3, Verified Crews, means the technician who arrives is background-checked, uniformed, and identified by name before the truck turns into your driveway. We also service Lennox, Trane, and Carrier systems, so when a New Braunfels home has mixed-brand zoning or a recent replacement that didn’t match the original, we don’t guess at compatibility.
The documented photo record, included on every visit, lets you verify the work against what you were told. Since our first job in 2013, we’ve served over 52,000 homes with this standard. No exceptions.
FAQs
No, provided the work is performed by a qualified technician using manufacturer-specified methods and no components are altered beyond their design intent. As an independent Honeywell service provider, we follow Honeywell’s published maintenance guidelines and document our process so warranty claims remain valid if a unrelated failure occurs later. Call (830) 549-6847 if you need a copy of our method statement for your warranty file.
Replacement is only necessary when fin corrosion has penetrated to the copper tubing or when refrigerant leaks are confirmed with electronic detection. In our New Braunfels inspections, roughly 85% of coils that homeowners were told needed replacement only required thorough cleaning and fin combing. We show you the borescope image and explain the difference before quoting either service. Call (830) 549-6847 for a free inspection.
Short-cycling after our humid March-May season usually indicates a fouled evaporator coil or a clogged condensate drain causing the float switch to interrupt operation. The T6 Pro and Prestige lines are particularly prone to this because their tight temperature control calls for more cycles per hour. Cleaning the coil and verifying drain flow typically resolves it without any control replacement. Call (830) 549-6847 to schedule diagnostics.
For consumables like humidifier pads and flame sensors, OEM Honeywell parts ensure proper fit and warranty compliance. For some electrical components, quality aftermarket parts meeting the same UL listing are acceptable and we note the manufacturer in our written scope. We never install unlisted generic parts, and we explain the trade-off before you approve the work. Call (830) 549-6847 for specifics on your system.
Every 3-5 years for the evaporator coil and blower, annually for the condenser if the outdoor unit is near construction or unpaved roads, and every 2 years for the humidifier pad and distribution system. Homes near Loop 337 or in developing areas like Veramendi tend to need more frequent condenser attention due to airborne particulate from active construction. Call (830) 549-6847 and we’ll set an interval based on your system’s environment.
Written by Tomas Reyes, Owner, CleanRun Air Duct Cleaning New Braunfels at CleanRun Air Duct Cleaning New Braunfels, serving New Braunfels and nearby areas.