Whole-system duct and dryer vent check with before-and-after photos - you see exactly what came out of your vents
That "$99 whole-house special" is a bait ad - the real number appears once they are in your hallway, or the "clean" is a shop-vac at the register. We photograph the inside of your ducts before and after instead.
Before
After
Before
After
Before
AfterAbatement Technologies Dryer Vent Cleaning in New Braunfels: What to Know First
We provide independent Abatement Technologies dryer vent cleaning in New Braunfels with written prices delivered before work starts and a documented photo record of every run. Most Abatement Technologies dryer vent jobs we handle in New Braunfels are completed in a single visit, with the full scope and price agreed in writing under Haven Standard Clause 1 before any panel comes off. This page is for homeowners who own an Abatement Technologies dryer vent system, have noticed longer dry times or a hot laundry room, and want to know what the repair should actually cost and what documentation they’ll receive when the crew leaves. Call (830) 549-6847 for a free estimate.
How Abatement Technologies Products Fail - and How We Fix Them
- CAP300 series vent caps seize in the open position. The CAP300’s louvered design uses a lightweight polymer hinge that fatigues after roughly four to six years in the Texas Hill Country’s UV exposure and temperature swings. When the louvers stick open, birds and wasps enter the duct run - we’ve pulled nests from CAP300 terminations in Canyon Lake-area homes more than once. We replace with a metal-bodied cap or install a bird guard, and we photograph the duct interior before quoting so you see what entered while the cap was stuck.
- HRV200 heat-recovery ventilators develop lint bypass at the core gaskets. The HRV200’s crossflow core sits downstream of some dryer vent configurations in tighter New Braunfels builds, and the silicone gasket set compresses permanently after sustained heat cycling. Lint bypasses the core and accumulates in the fresh-air intake, which the homeowner usually smells before they see. We remove the core, inspect the gasket lands with a borescope, and replace with high-temp silicone rated for dryer exhaust - not the generic door-gasket material some crews use.
- BDV series inline booster fans clog at the impeller. The BDV-100 and BDV-150 use a forward-curved impeller that moves high volumes at low pressure, but the blade geometry traps lint that makes it past a compromised screen. The fan runs louder, then hotter, then fails. We disassemble the housing, clean the impeller vanes with a soft brush (never a wire wheel - it throws the balance off), and test static pressure across the assembly before reinstallation.
- Flex duct adapters crack at the barbed fitting. Abatement Technologies’ flex-to-rigid adapters, common in the PVS series vent kits, use an ABS barb that becomes brittle where it passes through the wall thimble. The crack is hairline and hidden by the escutcheon plate; we find it with a smoke pencil during our negative-pressure test. We replace with a metal transition fitting and seal with high-temp foil tape, not duct tape - the adhesive fails at 140°F, which a long dryer cycle exceeds.
- RVP200 rooftop terminations lose their storm collar seal. The RVP200’s base flange relies on a compression seal against the roof jack, and the EPDM gasket shrinks faster in New Braunfels than in cooler climates - we’ve measured 3/16-inch gaps on ten-year-old units in the Solms area. Water enters, lint cakes, and the duct run corrodes from the top down. We reseat the termination with a new gasket and stainless hardware, and we run a camera down to document the duct condition below the penetration.
Our Abatement Technologies Dryer Vent Cleaning Process
- 1
Inspection with photo documentation. We insert a borescope at the termination and at the dryer connection, photographing every foot of the duct run. Tomas Reyes started this practice in 2013: show the photo first, explain what you’re looking at, then talk about what happens next.
- 2
Written scope and price. We deliver a written price before any work starts, under Haven Standard Clause 1. The scope names the Abatement Technologies components involved, the cleaning method, and any parts replacement with OEM or quality aftermarket alternatives.
- 3
Negative-pressure extraction. We connect a Nikro or Abatement Technologies portable HEPA vacuum to the duct run and agitate deposits with a Rotobrush flexible shaft, working from the termination inward to avoid pushing lint toward the dryer.
- 4
Component-specific service. Caps are removed and cleaned separately; inline fans are tested for amp draw and vibration; transitions are smoke-tested for leakage. We note Abatement Technologies part numbers on the work order for your records.
- 5
Post-clean verification. We photograph the cleaned duct run, measure airflow at the termination with an anemometer, and compare to the manufacturer’s spec for your dryer model. The before-and-after photo record is delivered as a standard job document.
- 6
Written guarantee. Every job concludes with the 365-Day Done Right Promise in writing. If the work is not right, we make it right.
BeforeAfterWhat Abatement Technologies Dryer Vent Cleaning Costs in New Braunfels
Most Abatement Technologies dryer vent cleaning jobs in New Braunfels fall between $189 and $349, with the final price set by duct length, accessibility, and whether component replacement is needed. A standard single-story vent run with a CAP300 cap cleaning and bird guard installation typically lands at the lower end. RVP200 rooftop terminations requiring ladder work and resealing, or BDV booster fan disassembly, push toward the higher end. We do not quote per-vent or per-foot add-ons; the written price covers the complete system. Call (830) 549-6847 for a free estimate - we’ll put our number next to any competitor’s written quote under our Free Second Opinion policy.
Why New Braunfels Homeowners Call CleanRun Air Duct Cleaning New Braunfels for Abatement Technologies Work
We’ve served over 52,000 homes since 2013, every one with a written price before work started and a documented photo record when the crew left. Our technicians are background-checked and uniformed under Haven Standard Clause 3: Verified Crews, and they arrive with equipment from Abatement Technologies, Rotobrush, Nikro, Honeywell, Aprilaire, and Guardsman - brands you can look up before we quote. We’re familiar with the Abatement Technologies product line, but we’re also fluent in Lennox, Trane, and Carrier systems, which matters in New Braunfels homes where the dryer vent interfaces with a mixed-manufacturer HVAC setup. The 365-Day Done Right Promise is backed in writing on every job, not stated in marketing copy and forgotten.
FAQs
No - independent service does not void the product warranty, provided the work is performed without damaging components. As an independent Abatement Technologies service provider, we document our methods and part numbers on the work order to support any future warranty claim you may file with the manufacturer. Call (830) 549-6847 if you need a copy of our service documentation for warranty purposes.
For wear items like gaskets and storm collars, quality aftermarket parts meet or exceed OEM specifications and are available without the four-to-six-week lead time we’ve seen on some Abatement Technologies backorders. For the HRV200 crossflow core specifically, we recommend OEM - the dimensional tolerance is tight, and aftermarket cores we’ve tested show higher pressure drop. We name the part source on every written scope before you approve it.
We deliver a before-and-after photo record of the full duct run as a standard job document, not as an upsell. The photo record shows the interior surface condition at multiple points, with timestamps. If a crew won’t show you the inside of the duct, you’re paying for noise, not work.
Attic duct runs are common in New Braunfels homes built 2015-2020, and they’re vulnerable to two local factors: attic temperatures exceeding 140°F in summer accelerate flex duct aging, and the Hill Country’s hard water mineral content can corrode metal terminations when condensation forms. We inspect attic runs with a thermal camera to identify hot spots indicating airflow restriction, and we document insulation condition around the duct as part of the photo record.
For a typical New Braunfels household of two to four people doing four to six loads weekly, every eighteen to twenty-four months is the interval we see produce clean ducts without excess wear on the system. Homes with pets, heavy towel use, or long duct runs (more than twenty-five feet) should schedule annually. We’ll tell you honestly if your system doesn’t need service yet - Haven Standard Clause 1 applies to declining work too.
Written by Tomas Reyes, Owner, CleanRun Air Duct Cleaning New Braunfels at CleanRun Air Duct Cleaning New Braunfels, serving New Braunfels and nearby areas.